Prototipe Sistem Monitoring dan Kendali Suhu Box Kubikel 20 kV Berbasis Long Range (LoRa)

Authors

  • Muhamad Ariandi Universitas Bina Darma, Palembang
  • Yoza Risti Oktaria Universitas Bina Darma, Palembang

DOI:

https://doi.org/10.30865/mib.v7i4.6796

Keywords:

Cubicle Box, ESP32, DHT 22 Sensor, SCT013 Sensor, LoRa

Abstract

Electricity distribution often faces problems, one of which is interference with the 20 kV cubicle box caused by corona due to changes in temperature and condensation. This disturbance can cause arcing between the insulator and live parts. One solution is to use a heater and exhaust fan to maintain temperature and humidity. This study proposes a prototype to combine temperature and control heaters and exhaust fans automatically. Integrated sensors help monitor the temperature in the cubicle. Using a temperature sensor (DHT 22) shows high accuracy, and a current sensor (SCT 013) is suitable for exhaust fans and heaters. When the sensor is ready, the DHT 22 sensor will read the temperature in the room. If the reading temperature exceeds 40°C, then the exhaust fan will turn on to remove hot air in the cubicle box, whereas if the temperature is below 40°C the heater will turn on. If the detected temperature exceeds 43°C, and the exhaust fan does not turn on, a notification will appear on Blynk to immediately check the exhaust fan for errors. Meanwhile, if the temperature detects the cubicle box below the temperature of 37°C, a heater error notification will appear. The SCT 013 current sensor will detect the amount of current flowing in the exhaust fan and heater with the help of Esp32 as a microcontroller. This prototype utilizes LoRa technology for remote communication and sends notifications via the Blynk application. Tests show that this tool can help operators effectively monitor and control cubicle box temperature.

References

A. Anantama, A. Apriyantina, S. Samsugi, and F. Rossi, “Alat Pantau Jumlah Pemakaian Daya Listrik Pada Alat Elektronik Berbasis Arduino Uno,†J. Teknol. dan Sist. Tertanam, vol. 1, no. 1, p. 29, 2020, doi: 10.33365/jtst.v1i1.712.

L. Gitleman and J. Kleberger, “Pengembangan Rancangan Bangun Pendeteksi Gejala Korona Pada Kubikel Tegangan Menegah (TM) 20KV Berbasis Spektrum Suara,†Pap. Knowl. . Towar. a Media Hist. Doc., 2014.

N. W. A. Sanjaya, D. R. Sawitri, and D. A. Asfani, “Pemodelan Busur Api Listrik Tegangan Rendah Berbasis Jaringan Syaraf Tiruan,†Eprints.Dinus.Ac.Id, 1999.

S. E. Lina, “Pemeliharaan Sistem Jaringan Distribusi Pt. Pln Mustika Asahan Jaya Aek Loba,†2022.

M. Y. Pratama and N. Fithri, “Prototype Sensor Suhu pada Sistem Monitoring Kubikel Berbasis Arduino,†Bina Darma Conf. Eng. Sci., vol. 2, no. 2, pp. 176–185, 2020.

M. Gembong, A. Rahman, and S. Broto, “Perancangan Sistem Kontrol Suhu Dan Kelembapan Udara Pada Kubikel 20Kv Berbasis Internet of Things ( Iot ),†vol. 3, no. 2, pp. 440–450, 2020.

A. Rahmadani, N. A. Windarko, and L. P. S. Raharja, “Rancang Bangun Sistem Monitoring Suhu dan Kelembapan serta Kendali Dua Heater pada Kubikel 20 kV Berbasis Sistem Informasi Geografis,†Maj. Ilm. Teknol. Elektro, vol. 21, no. 2, p. 219, 2022, doi: 10.24843/mite.2022.v21i02.p09.

K. V Berbasis, M. Di, and B. Udara, “RANCANG BANGUN MONITORING KORONA PADA KUBIKEL,†pp. 2–8, 2022.

A. Denhas, B. D. Sulo, and O. Melfazen, “Rancangan Preventive Condition Based Maintenance Berbasis Arduino Mega 2560 Untuk Pmcb Di Jaringan Pln Up3 Pasuruan,†Sci. Electro, pp. 1–6, 2019, [Online]. Available: http://www.riset.unisma.ac.id/index.php/jte/article/view/3487%0Ahttp://www.riset.unisma.ac.id/index.php/jte/article/download/3487/3178

D. P. Darmawan, E. Suryani, and H. Fabroyir, “Monitoring Tegangan Gardu Trafo Tiang Menggunakan IoT Berbasis Lorawan pada PLN Distribusi Jawa Timur,†vol. 8, no. 3, 2023.

F. Purwaningtias, M. Ariandi, and M. Ulfa, “Visualisasi Data Kriminal Wilayah Polres Musi Banyuasin,†vol. 10, no. 1, pp. 193–202, 2023, doi: 10.25126/jtiik.2023105658.

A. R. Madjid and B. Suprianto, “PROTOTYPE MONITORING ARUS , DAN SUHU PADA TRANSFORMATOR DISTRIBUSI BERBASIS INTERNET OF THINGS ( IoT ),†Jur. Tek. Elektro Fak. Tek. Univ. Negeri Surabaya, pp. 111–119, 2019.

C. O. S. Patricia, “Alat Kontrol Monitoring Suhu dan Kelembaban Pada Sistem Distribusi Tenaga Listrik Kubikel 20 kV Berbasis Website,†vol. 3, no. 2, p. 6, 2021.

S. Sembiring, H. Kaban, and R. Zulfahmi, “Perancangan Sistem Efisiensi Penggunaan Energi Listrik Menggunakan Sensor Gerak dan Sensor Arus,†J. Media Inform. Budidarma, vol. 4, no. 3, p. 626, 2020, doi: 10.30865/mib.v4i3.2134.

Harifuzzumar, F. Arkan, and Ghiri Basuki Putra, “PERANCANGAN DAN IMPE LEMENTASI ALAT PEMBE RIAN PAKAN IKAN LELE OTOM ATIS PADA FASE PENDEDERAN BERBASIS ARDUINO DAN APLIKASI BLYNK,†vol. 02, 2018.

F. B. Awi, A. Rabi, and W. Dirgantara, “Pengimplementasian Metode Fuzzy Logic pada Kontrol Rumah Jamur Otomatis Berbasis Node-RED,†J. Tek. Elektro Dan Komput. Triac, vol. 9, no. 3, 2022, [Online]. Available: https://journal.trunojoyo.ac.id/triac

K. Fatmawati, E. Sabna, and Y. Irawan, “Rancang Bangun Tempat Sampah Pintar Menggunakan Sensor Jarak Berbasis Mikrokontroler Arduino,†Riau J. Comput. Sci., vol. 6, no. 2, pp. 124–134, 2020.

M. Ariandi and J. Alvinser, “Prototipe Sistem Monitoring Rumah Walet Berbasis IoT,†vol. 7, no. April, pp. 920–927, 2023, doi: 10.30865/mib.v7i2.5897.

A. Afdillah and A. I. Agung, “Rancang Bangun Alat Pendeteksi Suhu dan Kelembaban sebagai Pencegahan Kegagalan Isolasi pada Kubikel,†J. Tek. Elektro Unesa, vol. 8, pp. 703–709, 2020.

B. F. Alwaaritsi, T. Tohir, and D. Aming, “Rancang Bangun Sistem Kontrol dan Pemantauan Serikultur Menggunakan Mikrokontroler Berbasis Internet-of-Things,†Pros. Ind. Res. Work. Natl. Semin., vol. 12, pp. 41–46, 2021, doi: 10.35313/irwns.v12i0.2654.

A. F. H. Sitanggang and Y. A. Prabowo, “Perancangan Alat Monitoring Arus Bocor pada Kabel 20 kV Menggunakan Filter Kalman Berbasis Internet of Things,†Elektrika, vol. 14, no. 2, p. 41, 2022, doi: 10.26623/elektrika.v14i2.4849.

Downloads

Published

2023-10-22

Issue

Vol. 7 No. 4 (2023): Oktober 2023

Section

Articles

License

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License

Authors who publish with this journal agree to the following terms:

  1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under Creative Commons Attribution 4.0 International License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
  2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
  3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (Refer to The Effect of Open Access).